Eliteflyer

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 22 total)
1 2
  • Author
    Posts
  • 28/01/2025 at 10:36 #4078
    Eliteflyer
    Participant

    Hi

    Your trim is activated. According to your screen shots.
    Your Firmware is way out of date, try updating it via the forum site. It should be about 745 now. But check.
    Its easy to do, it does it automatically.
    If your looking at the zero for trim in the three boxes on your screen shots, that doesn’t mean the trim is not active. Make sure you save any changes!!
    Have you tried it on your aircraft?

    27/01/2025 at 17:44 #4073
    Eliteflyer
    Participant

    If you go to trim tab in the manual, it explains everything. Cant quite understand why your pic shows hydraulics!

    There is also some good advise on youtube.

    23/01/2025 at 14:38 #4060
    Eliteflyer
    Participant

    I will try and forward.

    Attachments:
    You must be logged in to view attached files.
    23/01/2025 at 13:58 #4059
    Eliteflyer
    Participant

    Hi

    Do you have the CLS2SIM Manual?

    Eliteflyer

    23/01/2025 at 10:40 #4057
    Eliteflyer
    Participant

    Do you not have to be a account holder with access password to use CANopen?

    I always use CLS2SIM to access and change force values.
    Maybe wrong!!

    16/12/2024 at 08:59 #4032
    Eliteflyer
    Participant

    Hi

    Just make sure that Brunner is ticked in the EFB.
    Otherwise the yoke goes all over the place!!
    I had replies from Brunner just after xplane 12 came out that there is not a compatability problem with xplane 12.

    20/08/2024 at 11:57 #3894
    Eliteflyer
    Participant

    Hi

    You would get a better response if you posted a ticket on tech. support page.
    Diego is usually very quick to respond and would almost certainly know what the problem is.

    Regards

    Eliteflyet

    08/07/2024 at 09:02 #3862
    Eliteflyer
    Participant

    Try this

    Attachments:
    You must be logged in to view attached files.
    22/03/2024 at 09:09 #3761
    Eliteflyer
    Participant

    Hi

    I have always found them listed in the changelog file that is downloaded with the firmware update.
    You can also find a copy in the Brunner site software download section.
    Trust this helps

    Eliteflyer

    29/01/2024 at 10:33 #3729
    Eliteflyer
    Participant

    That did it👍👍👍👍

    29/01/2024 at 10:32 #3727
    Eliteflyer
    Participant

    Hi

    If you cant find it, the manual, I can email it to you.

    One more attempt😜

    Attachments:
    You must be logged in to view attached files.
    29/01/2024 at 10:11 #3726
    Eliteflyer
    Participant

    Hi

    No good. See your email

    29/01/2024 at 10:11 #3725
    Eliteflyer
    Participant

    Whoops

    Seems its to big for the forum.

    See cut version lets hope.

    29/01/2024 at 10:09 #3724
    Eliteflyer
    Participant

    Hi

    Sent an email with front page of the manual. I will send again here.

    Eliteflyer

    28/01/2024 at 10:29 #3722
    Eliteflyer
    Participant

    Hi

    Have you acquired the CLS2SIM instruction manual from Brunner. This has some salient points regarding trim setup for various sins.

    Just a thought

    Regards

    Eliteflyer

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 22 total)
1 2